fychis
+86 19112905173

Safety precautions for cnc tube bending machine

Our cnc tube bending machine has been mature and stable in terms of quality and technology, so after purchasing the cnc tube bending machine, as long as you maintain it carefully and use it properly, the cnc tube bending machine can serve for a long time. This article will introduce the safety precautions and maintenance knowledge of the cnc tube bending machine in daily use.

cnc tube bending machine

What are the safety rules when using a tube bending machine?

(1) Check the surrounding of the work site and remove all sundries that hinder work and traffic. The ground should be clean and no oil to avoid slipping. Work pieces should be stacked neatly and firmly to prevent collapse.

(2) Check whether the protective device on the cnc tube bending machine is in good condition, if it is not installed, it is not allowed to start up the cnc tube bending machine. The cnc copper tube bending machine must have good grounding and good electrical insulation, and the voltage must be stable.

(3) Check the lubrication points of the tube bending machine cnc and add enough oil when there is lack of oil or no oil

(4) Check whether the mechanical operation of the cnc tube bending machine for sale is normal and whether the electrical switch is sensitive during the test run without work pieces. Start working with work pieces after confirming that the cnc tube bending machine for sale works well. When two operators work at the same time, they should closely cooperate and coordinate. An operator must be designated to operate the switch.

(5) When the cnc copper tube bending machine is working, the operator should not leave the workplace.When the cnc copper tube bending machine is working, it is forbidden to get close to the pipe bending stroke range. Warning signs should be set. Stand firmly when prying the tube to prevent being injured by the skid of the crowbar. Operators can only stand outside. Pay attention to the safety around when calibrating the tube. Before using the hammer, please soak in water for a few minutes to prevent the heavy hammer head from falling and hurting people. Do not wear gloves when hammering at the tube.

(6)In case of emergency when you operate the cnc tube bending machine, please press the emergency stop button, then turn the switch to manual position, restart it manually. If there is a fault, please report for repair in time.

(7)Cut off the power supply of the cnc tube bending machine and do a good job of cleaning and lubrication after finishing work.

If you need more infomations about safety rules when using a tube bending machine, you can check our blog tube bending machine safety precautions, or contact us by whatsapp, we will give you suggestions accoding to your tube bending machine model.

Key points of daily maintenance of cnc tube bending machine

1, Do not place the cnc tube bending machine in a place where the sun shines directly, to avoid the sun exposure which will cause the cnc tube bending machine to deform and crack.

2, The table top of the cnc tube bending machines should be kept as clean and tidy as possible. Do not stick tapes and other items on the table, and do not scribe on the table. If there is dust on the cnc tube bending machines, please wipe them with a damp towel and soapy water. Do not use alcohol, banana oil or other corrosive chemicals to wipe the cnc tube bending machines.

3, If it is difficult to move the front and rear right-angle slides and the left and right rulers during the use of the cnc tube bending machine, please clean up the dust and debris in the track and use 4B-B pencil lead to scribble back and forth on both sides of the sliding track and the lower guide rail of the sliding plate, then the right-angle slides and the rulers can slide smoothly.

cnc tube bender

Conclusion: The operation control method of the cnc tube bending machines is relatively simple, however, users still need to know the use requirements and operating rules of the cnc tube bending machines and master the skill. In this way, in the actual operation and use, it can not only improve the efficiency of the cnc tube bending machines, but also make the most of the advantage in the use of the cnc tube bending machines, and also can help to prolong the service life of the cnc tube bending machines. To learn more about our cnc tube bending machines you can visit our website.

How to reduce wear in the use of cnc tube bending machine?

1.The iron filings behind the guide rail of the tube bending machine cnc should be cleaned frequently to ensure that the front and rear dust covers of the guide rail are intact. For the outlet track of the tube bending machine cnc, new grease should be added every week to reduce wear.

2.Add grease to the clamping cylinder bearing, clamping cylinder and slider every week or every two weeks.

3.Cleaning and lubrication must be carried out every year for the rest of the bearings of the cnc tube bending machine.

4.The front and rear bearings of the main shaft of the cnc tube bending machine should be coated with high-speed grease, and the main shaft box adopts mechanical seal, so there is no need to add grease. If you need mores details about reducing wear in the use of cnc tube bending machine, you can click our blog Methods to reduce tube bending machine wear and rust removal.

clamping cylinder of tube bending machine cnc

We are one of the higher reputation cnc tube bending machine manufacturers in China. We push for sale our cnc tube bending machine in India, Pakistan, Vietnam, Chile, Mexico, and get very good feedback from our customers. If you have technical questions about cnc tube bending machine, don’t hesitate to contact us, we will be happy to help you solve them.

cnc square tube bending machine

● Similar Posts

COPYRIGHT 重庆鑫锐科信息科技中心@2022